The SmartFeed 2.0 is programmed directly on the device and is ideal if you prefer simple and straightforward operation. You can schedule up to three feedings per day with individually adjustable portion sizes and intervals of 24, 48, or 72 hours.

The SmartFeed AppControl is the logical evolution of the SmartFeed 2.0 and is fully controlled via the MyJUWEL App. This gives you complete control over feeding your fish – anytime and anywhere – conveniently via your smartphone.
With the MyJUWEL App, you can schedule up to twelve feedings per day, adjust the feeding quantity in eight levels, and also feed manually. All settings can be changed flexibly – no matter where you are. Additionally, you’ll receive notifications when the feed level is low – so your fish are always reliably supplied.

Both models come with interchangeable feed screws for optimal dispensing of different types of food.

Yes, a smartphone is required to operate the SmartFeed AppControl. Setup and operation are carried out via the MyJUWEL App, which must be installed on an Apple iOS or Android device. The app guides you step by step through the setup and allows for intuitive control.

Please note: To connect with the MyJUWEL App, a Wi-Fi network operating at 2.4 GHz or dual-band 2.4/5 GHz is required. A mobile hotspot is not sufficient for this.

Please make sure that both Bluetooth and location services are enabled on your smartphone.

Important: Even if location access has already been granted in the app, the location service must also be activated in your phone’s system settings. Your location is not stored – it is only required to detect new devices within your network.

For a stable connection, we recommend placing the SmartFeed AppControl close to your router during setup.

Yes, in order for the MyJUWEL App to correctly detect and connect to your SmartFeed AppControl, location data must be enabled.

Don’t worry: this does not involve GPS data – your actual location is not being recorded.
Wi-Fi devices communicate via the names of nearby networks. According to legal requirements, this network information is considered location data because it could theoretically indicate your position. This is why the system is required to display a corresponding message.

Important to know: This data is not transmitted to our servers. It is used exclusively to enable the connection between your smartphone and the device.

Press and hold the control button for at least 10 seconds within 30 seconds of connecting the device to a power source.
If the reset was successful, the green and blue LEDs will flash quickly three times in succession.

In factory default mode: After connecting the device to the power supply, it automatically enters pairing mode (LED signal: short, short, long). Now open the MyJUWEL App and follow the instructions for setup.

If the LED signal does not appear, you can manually activate pairing mode by performing a factory reset (see above).

Next, select your 2.4 GHz Wi-Fi network, enter the Wi-Fi password, and make sure you are within range of your router.
The connection is successful when the blue LED lights up continuously.

If your SmartFeed AppControl is correctly set up but still appears as “offline” in the app, this may have the following causes:

• The device cannot connect to your Wi-Fi or is out of range. In this case, the blue LED flashes briefly at regular intervals.

Solution:

• Restore factory settings:

  Press and hold the control button for at least 10 seconds within 30 seconds after connecting the device to power.
  The green and blue LEDs will flash rapidly – the device is now in pairing mode. Start the setup process in the app again.

• Activate Bluetooth:

  Make sure Bluetooth is enabled on your smartphone.

• Keep devices close together:

  Ensure that your smartphone and the SmartFeed AppControl are close to each other during setup.

On the device:

Briefly press the control button – the device will feed automatically using the preset amount (⅛). You can adjust the amount in the app.

Via the app:

Start the feeding manually and conveniently using the MyJUWEL App – with your individually set feed quantity.

Using voice command:

Use voice control via Amazon Alexa or Google Assistant with the command:
  “Start feeding”
To do so, voice control must first be activated in the MyJUWEL App.

• Blue flashing (short, short, long): Pairing mode active
• Blue flashing regularly: Connecting to Wi-Fi
• Blue continuously on: Wi-Fi connection successful
• Green continuously on: Normal operation, feed chamber sufficiently filled
• Green flashing (1 second): Low feed level
• Green flashing rapidly: Mechanical error (e.g. jammed feed screw)

The SmartFeed AppControl operates exclusively on the 2.4 GHz frequency band.
Please ensure that your router is running in 2.4 GHz mode or dual-band mode (2.4 / 5 GHz).

Disconnect the device from the power supply before cleaning.
Use a soft cloth and lukewarm water – do not use harsh cleaning agents.
We recommend checking the SmartFeed AppControl for dirt about every four weeks and cleaning it if necessary using the included cleaning brush. This ensures hygienic and reliable feeding.

Yes, after setup in the MyJUWEL App, you can control your SmartFeed AppControl using Amazon Alexa or Google Assistant.

Available voice commands:

•  “Start feeding” – immediately starts feeding with the predefined amount
•  “Set feed quantity to X (1–8)” – adjusts the feed quantity

Note: Voice commands are currently available in German and English.